Bolt Circle Calculator

X/Y coordinates for evenly spaced holes on a bolt circle, in inches or millimeters, with the angle convention always shown.

Hole pattern

Units

1 to 360.

Center to center across the pattern.

Measured from +X (3 o’clock), counterclockwise positive.

Hole 1 at:
Number the holes

Results

0° = +X (3 o’clock), angles increase counterclockwise. Holes are numbered counterclockwise from hole 1 at 0°.

+X+Y123456⌀ 4.0000 in bolt circle
Hole 1 is filled. Viewed with +X to the right and +Y up.
Angle between holes
60°
360° ÷ 6 holes
Hole-to-hole distance
2.0000 in
D × sin(180° ÷ 6)
Radius
2.0000 in
Diameter 4.0000 in
Hole 1
X 2.0000 Y 0.0000
Hole 1 at 0°, then counterclockwise

Coordinates

HoleAngleX (in)Y (in)
10°2.00000.0000
260°1.00001.7321
3120°-1.00001.7321
4180°-2.00000.0000
5240°-1.0000-1.7321
6300°1.0000-1.7321
Built-in checks
Every hole is 2.0000 in from the center (largest deviation 0 in).
Average of all hole positions: X 0.0000, Y 0.0000 — the center, as it should be.
Neighboring holes are 2.0000 in apart, center to center.

Verify orientation against your drawing datum and fixturing before cutting. This tool does not generate G-code.

How the bolt circle calculator works

The holes sit on a circle of diameter D around a center (cx, cy), evenly spaced 360° ÷ n apart. Hole 1 is at the start angle; the others follow counterclockwise or clockwise.

r      = D ÷ 2
θᵢ     = start + s × i × 360° ÷ n     (i = 0 … n − 1; s = +1 CCW, −1 CW)
xᵢ     = cx + r × cos θᵢ
yᵢ     = cy + r × sin θᵢ
chord  = D × sin(180° ÷ n)            (distance between neighboring holes)

Angle convention

Angles are measured from the +X axis (the 3 o’clock position) and increase counterclockwise, the standard math convention. It is also how Fanuc-style G16 polar coordinates are commonly described (for example byCNCCookbook). Some calculators and drawings instead measure from 12 o’clock or clockwise, so the convention is printed above the results at all times. For hole 1 at 12 o’clock, use a start angle of 90°.

Example: 6 holes on a 4 in circle

r = 2 in and the holes are 60° apart. Starting at 0°: hole 1 is at (2.0000, 0.0000), hole 2 at (1.0000, 1.7321), hole 3 at (−1.0000, 1.7321) and so on. Neighboring holes are 4 × sin 30° = 2.0000 in apart.

Built-in checks

Below the table the calculator confirms three things from the computed coordinates themselves: every hole is exactly one radius from the center, the average of all hole positions is the center, and neighboring holes are one chord apart. If you edit the numbers by hand, these are quick ways to catch a sign or angle error.

Limitations

Evenly spaced holes on one circle. Unequal spacing, partial patterns and G-code output are not supported. Coordinates are rounded for display (4 decimals in inches, 3 in mm); the CSV uses the same rounding. Always check the result against your print and machine setup.

Frequently asked questions

How do I find the distance between bolt holes?

Chord = D × sin(180° ÷ n). For 4 holes on a 100 mm circle: 100 × sin 45° = 70.711 mm.

What is the X/Y of 8 holes on a 4 in circle starting at 22.5°?

Hole 1 is at (1.8478, 0.7654); each next hole is 45° further around.

Last updated . Found an error? Let us know.