Roof Pitch Calculator

Convert between rise and run, pitch in inches per foot (x/12) and degrees, with the slope multiplier.

What you know

Units
Start from

Vertical height.

Horizontal distance.

Geometry only. This tool converts slope measurements; it does not check whether a slope suits a roofing material, drains properly or meets code.

Results

Roof pitch
6/12
26.57° · 50% grade
26.57°Run 12 inRise 6 in
Angle drawn true; lengths not to scale
Angle
26.57°
Degrees above horizontal
Pitch
6/12
Inches of rise per foot of run
Percent grade
50%
Rise ÷ run × 100
Rise : run
1 : 2
Run per unit of rise
Slope multiplier
1.118
Sloped length ÷ horizontal run
Sloped length
13⅜ in
Along the slope, for 12 in of run
How this was calculated
Slope: rise ÷ run = 0.5 ft ÷ 1 ft = 0.5
Pitch: 0.5 × 12 = 6/12
Angle: arctan(0.5) = 26.57°
Percent grade: 0.5 × 100 = 50%
Multiplier: √(1 + 0.5²) = 1.118
Sloped length: √(rise² + run²) = 1 ft 1⅜ in

Sloped length is measured along the roof surface for the run you entered; it excludes overhangs, ridge deductions and rafter cuts.

How roof pitch is measured

Pitch compares how far a roof rises to how far it runs horizontally. In the US it is written as inches of rise per 12 inches (one foot) of run: a 6/12 roof rises 6 in for every foot. The same slope can be written as an angle, a percentage or a ratio. All of them come from one number, the slope = rise ÷ run.

slope       = rise ÷ run                  (same units for both)
pitch (x/12) = slope × 12
angle       = arctan(slope)
percent     = slope × 100
multiplier  = √(1 + slope²) = 1 ÷ cos(angle)
sloped length = run × multiplier = √(rise² + run²)

Example: a 6/12 roof

Slope = 6 ÷ 12 = 0.5. The angle is arctan(0.5) = 26.57°, the grade is 50%, and the multiplier is √1.25 = 1.118: every 10 ft of horizontal run is 11.18 ft measured along the roof.

Measuring pitch on a real roof

Hold a level horizontally against the roof surface or a rafter, measure 12 in along the level, and measure straight down (or up) from that mark to the roof. That distance in inches is the x in x/12. You can also measure from inside the attic on a rafter. Work safely: you do not need to be on the roof to measure pitch.

Using the slope multiplier

Multiply a horizontal measurement by the multiplier to get the length along the slope. For a simple gable roof, the plan area (footprint including overhangs) × multiplier gives the sloped roof area. Hips, valleys and dormers need more than one multiplier, so measure those sections separately.

Common pitches

PitchAngleGradeMultiplier
1/124.76°8.3%1.0035
2/129.46°16.7%1.0138
3/1214.04°25%1.0308
4/1218.43°33.3%1.0541
5/1222.62°41.7%1.0833
6/1226.57°50%1.118
7/1230.26°58.3%1.1577
8/1233.69°66.7%1.2019
9/1236.87°75%1.25
10/1239.81°83.3%1.3017
12/1245°100%1.4142
18/1256.31°150%1.8028
24/1263.43°200%2.2361

Limitations

This calculator converts slope measurements. It is not a structural or code assessment: minimum slopes for shingles, metal or membranes, snow and wind loads, rafter sizes and ventilation are set by manufacturers and your local building code.

Frequently asked questions

What angle is a 4/12 roof?

arctan(4 ÷ 12) = 18.43°. Its grade is 33.3% and its multiplier 1.0541.

What pitch is a 45° roof?

12/12: it rises one foot for every foot of run. Its multiplier is √2 ≈ 1.4142.

Last updated . Found an error? Let us know.