Gravel & Crushed Stone Calculator

Cubic yards, weight in tons and bags of gravel or crushed stone for an area at the depth you need.

Area to cover

Units
Shape
L 20 ftW 10 ftD 3 in
Schematic, not to scale
ft

ft

in

Thickness of the layer you are adding. You can type 2 1/2.

1.40 tons per cubic yard of loose gravel or crushed stone (MoDOT estimating factor). Use your supplier’s figure if you have it.

For compaction, uneven ground and spillage. Your choice: see below.

Bagged gravelOptional · count bags by weight

The weight printed on the bag.

Results

Gravel to order (incl. extra)
2.85tons
2.04 cu yd · incl. 10% extra
Volume
2.04 cu yd
55.0 cu ft · 1.56 m³
Weight
5,704 lb
2.59 metric t
Area
200 sq ft
3 in deep
Density used
1.4 tons/cu yd
= 1.661 t/m³
How this was calculated
Area: 20 ft × 10 ft = 200 sq ft
Depth: 3 in ÷ 12 = 0.25 ft
Volume: 200 × 0.25 = 50 cu ft
÷ 27 = 1.852 cu yd
+ 10% extra = 2.037 cu yd (55 cu ft)
Weight: 2.037 cu yd × 1.4 tons/cu yd = 2.852 tons (5,704 lb)

Weight depends on the stone, its moisture and how tightly it is packed. Confirm the density and the order unit (ton or cubic yard) with your supplier.

How the gravel calculator works

Gravel is ordered by volume (cubic yards) or by weight (tons). The calculator finds the volume of the layer first, adds your extra percentage, and then converts volume to weight with a density you can see and change.

Area (sq ft)    = length × width        (rectangle)
                = π × (diameter ÷ 2)²   (circle)
Volume (cu ft)  = area × depth (in) ÷ 12
Cubic yards     = cubic feet ÷ 27
To order        = cubic yards × (1 + extra %)
Tons            = cubic yards to order × density (tons per cu yd)
Bags            = tons × 2,000 ÷ bag weight (lb), rounded up

Example: a 20 × 10 ft path, 3 inches deep

The area is 200 sq ft. At 3 in (0.25 ft) deep that is 50 cu ft, or 1.85 cu yd. With 10% extra you need 2.04 cu yd. At 1.40 tons per cubic yard that is 2.85 tons, about 5,700 lb.

Density: the number that turns yards into tons

There is no single weight for “a yard of gravel”. It depends on the rock, the size and shape of the stones, how wet they are, and whether the material is loose (as delivered) or compacted. The default of1.40 tons per cubic yard is the figure for loose “gravel, crushed stone and chat” in the Missouri Department of Transportation’s estimating factors (2009 edition). The same document lists compacted aggregate base course at 0.058 tons per square yard per inch of depth, which works out to about 2.09 tons per cubic yard: packed material is much heavier per yard.

Many quarries and landscape yards publish a weight for each product. If yours does, type it into the Density field. In metric mode the field uses tonnes per cubic meter (1.40 tons/yd³ ≈ 1.66 t/m³).

Choosing the extra percentage

The calculator measures the space to fill. You will usually need more loose stone than that: compacting a layer squeezes it down, the ground is never perfectly even, and some stone is lost at the edges. We did not find an authoritative single allowance for this, so the extra is yours to set. The 10% default covers small irregularities; if you plan to compact a base course, ask your supplier how much extra they recommend for that material.

Common mistakes

  • Depth in feet. 3 inches is 0.25 ft. Keep the depth field in inches (or cm).
  • Mixing up tons and yards. A cubic yard of gravel weighs more than a ton. Check which unit your supplier sells in.
  • Using the compacted depth with a loose density. If you compact, add extra for the volume lost.

Limitations

One rectangular or round area per calculation; for an L-shaped driveway, add up two rectangles. The calculator does not design a driveway or a base course: required depth and material depend on use, soil, drainage and local rules.

Frequently asked questions

How many tons of gravel are in a cubic yard?

It depends on the material. For estimating, MoDOT uses 1.40 tons per cubic yard of loose gravel or crushed stone. Compacted base material is heavier. Your supplier’s product weight is the best number to use.

How much area does a ton of gravel cover?

At 1.40 tons per cubic yard, one ton is about 0.71 cu yd (19.3 cu ft). Spread 3 in deep that covers about 77 sq ft; at 2 in, about 116 sq ft.

Can I use this for sand or road base?

Yes, if you enter that material’s density. The volume math is the same for any loose material.

Last updated . Found an error? Let us know.