Deck Calculator

Deck boards, joist count and face screws for a rectangular deck: a material list, not a structural design.

Deck size

Units
L 16 ft · boards run this wayW 12 ftjoists 16 in o.c.
Plan view, schematic, not to scale
ft

ft

Joists run this way.

in

A 2×6 is 5½ in wide. Measure yours.

in

Use the board maker’s spacing.

ft

Longer boards mean fewer joints.

in

Center to center, from your plan.

Cuts, defects and offcuts. Added to boards and screws.

Results

Deck boards to buy
29boards
16 ft boards · 26 + 10% waste
Joists
13
16 in on center
Face screws
744
2 per board at each joist · incl. 10%
Rows of boards
26
Last row ripped to 3⅜ in
Decking installed
416 ft
Decking installed, before waste
Deck area
192 sq ft
16 ft × 12 ft
Joints
One board per row
Butt joints are placed over joists

Material list

Deck boards, 16 ft29
Joists, 12 ft span direction13
Face screws (2 per board per joist)744

Not included: joist and beam sizes, rim joists, ledger, beams, posts, footings, hangers, railing and stairs. Those are structural and must follow your plan and local code.

How this was calculated
Rows: (144 in + 0.125 in gap) ÷ (5.5 in board + 0.125 in gap) = 25.62 → 26 rows
Each row: 16 ft fits on one 16 ft board
Boards: 26 rows × 1 = 26
+ 10% waste = 28.6 → 29 boards
Joists: 192 in ÷ 16 in = 12 → 12 bays + 1 = 13 joists
Screws: 26 rows × 13 joists × 2 = 676
+ 10% waste = 744 screws

How the deck calculator works

Boards run the length of the deck, side by side across its width. Joists run the other way, under the boards, spaced along the length. The calculator counts rows of boards, the stock boards each row needs, the joists, and two face screws wherever a board crosses a joist.

Rows    = (width + gap) ÷ (board width + gap), rounded up
Boards  = rows × boards per row, + waste %
          one board per row if it is long enough; otherwise boards
          up to a joint use whole joist bays (every joint on a joist)
          and the last board runs to the end of the row
Joists  = length ÷ joist spacing, rounded up, + 1
Screws  = rows × joists × 2, + 2 per butt joint, + waste %

Example: a 16 × 12 ft deck

With 5½ in boards and a ⅛ in gap, each row takes 5⅝ in: (144 + ⅛) ÷ 5⅝ = 25.6, so 26 rows, with the last row ripped to 3⅜ in. 16 ft boards cover a row in one piece, so 26 boards, or 29with 10% waste. Joists 16 in on center: 192 ÷ 16 = 12 bays, so 13 joists. Screws: 26 × 13 × 2 = 676, or 744 with 10% extra.

Gaps, joints and fasteners

The American Wood Council’s Prescriptive Residential Wood Deck Construction Guide (DCA 6, 2015 edition) calls for two fasteners where a deck board crosses a joist: two #8 screws or two 8d threaded nails. It also notes a gap of about ⅛ in between boards and that each board should bear on at least three joists. Composite and PVC boards follow their maker’s instructions for gaps, fasteners and joist spacing, and many are installed with hidden fasteners instead of face screws. If you use those, ignore the screw count and follow the clip maker’s coverage.

When a row is longer than your boards, the calculator joins boards over a joist. A board that ends at a joint can only use whole joist bays, so a 10 ft board on joists 16 in on center contributes 9 ft 4 in (seven bays), not 10 ft. The last board in the row runs to the end of the deck and can use its full length. Each joint adds one more pair of screws for the second board end.

What this calculator does not do

It is a material take-off for the decking surface. It does not size joists or beams, check spans or loads, or design posts, footings, ledger attachment, guards or stairs, and its results are not a structural approval. Joist spacing and lumber sizes must come from your plan, the board manufacturer and your local building department. Many areas require a permit for decks.

Common mistakes

  • Using the nominal width. A 2×6 is 5½ in wide; dividing by 6 undercounts rows by about 8%.
  • Forgetting the end joist. Joists = bays + 1.
  • Joints between joists. Every butt joint must land on a joist, which can waste part of each board.

Limitations

One rectangular deck with boards laid straight (not diagonal or picture-framed). Fascia, rim joists, blocking, stairs and railings are not included. Offcuts are not reused between rows, so the board count leans slightly high. The count is the fewest boards with every joint on a joist; staggering joints between rows and keeping every piece over at least three joists (as DCA 6 recommends) can take more.

Frequently asked questions

How many joists do I need for a 12 × 16 deck?

If the joists are spaced along the 16 ft side at 16 in on center: 192 ÷ 16 = 12 bays, so 13 joists. At 12 in on center: 16 bays, 17 joists. Which side the joists span, and how far, depends on your structural plan.

How many screws per deck board?

Two at every joist the board crosses. A 16 ft board over joists 16 in on center crosses 13 joists: 26 screws.

Last updated . Found an error? Let us know.